Standing seam metal roofing installation in Florence, KY, done right the first time
Metal roof installation Florence KY built to outlast asphalt
Metal roof installation Florence KY is what we do for homeowners across Boone County who are tired of replacing asphalt shingles every 12 to 15 years. We install standing seam metal roofing installation in Florence on homes from Seven Points to Forest Hills, sized for Kentucky ice storms, summer hail, and the freeze-thaw cycle that chews up cheap roofs. If your shingles are curling, missing, or leaking, we can get a metal roof over your head in days, not weeks.
Live phone supportUpfront optionsBacked workmanship
What's included
What our metal roof installation includes
Every metal roof installation Florence KY project we quote covers the full assembly, not just panels. Here is what is included in a standard install, and what we price separately if your roof needs it.
Full tear-off and disposal
We strip existing shingles with a shingle remover, pull all nails, and haul everything to the dumpster. Decking gets inspected sheet by sheet, and any soft spots are flagged with photos before we go further.
Synthetic underlayment and ice shield
We roll synthetic underlayment across the entire deck and set ice and water shield along eaves, valleys, and penetrations. This is the waterproofing layer that protects your home if a panel is ever damaged.
Standing seam panels and clips
Panels are cut to length, locked seam by seam, and fastened with concealed clips so no fastener head is exposed. We install to manufacturer specs so your panel finish warranty stays valid.
New flashing and ridge vents
Chimney flashing, sidewall flashing, pipe boots, and ridge vents are all replaced, not reused. Proper attic ventilation keeps moisture from condensing on the underside of your panels in winter.
Final magnet sweep and walkthrough
We magnet-sweep the lawn and driveway for stray nails, then walk the roof and the attic with you. You get photos of the finished install and your warranty paperwork before we pack up.
Service overview
Metal roof installation Florence KY: what the job actually involves
Metal roof installation Florence KY is the process of stripping or covering your existing roof deck with interlocking steel panels, fastening them through a synthetic underlayment and ice and water shield, and sealing every penetration so water never touches the deck again. We start by pulling shingles with a shingle remover, checking the deck for rot with a moisture meter, then running a chalk line so every panel lands square. Panels get cut with tin snips and a utility knife, fastened with a roofing nail gun, and finished with ridge vents and new flashing.
Florence sits in a hail belt that dumps quarter-size stones on roofs in Mars Hill and Cloverdale most springs, and January ice dams are common on north-facing slopes. That is why so many homeowners here are moving to metal. A standing seam metal roof Florence Kentucky install sheds hail and ice instead of cracking like asphalt shingles. If you have been searching metal roof installation in Florence KY near me, we cover the whole city and Boone County, and we can usually get an estimate out within 48 hours.
How we workWe verify the cause, compare realistic options, and confirm the repair before we leave.
The service timeline
Our metal roof installation process, step by step
The process flexes to the condition, but these checkpoints keep decisions clear.
Inspection and estimate
We walk the roof, check the deck with a moisture meter, and scan for hidden leaks with an infrared camera. You get a written scope with panel gauge, color, and fastener type. Most estimates take 45 minutes, and you get pricing the same day.
Tear-off and deck prep
On a full tear-off, we strip shingles with a shingle remover, pull nails, and inspect every sheet of decking. Soft spots get replaced before anything goes back down. A typical 2,000 square foot roof takes one to two days to strip and prep.
Underlayment and flashing
We roll synthetic underlayment across the deck, then set ice and water shield along eaves, valleys, and penetrations. New flashing goes in at chimneys, vents, and sidewalls. This is the layer that keeps water out for the next 40 years.
Panel install
Panels are cut to length, hoisted, and locked together seam by seam. We fasten through the raised seam with concealed clips so no fastener head is exposed to weather. A crew of four sets roughly 800 to 1,200 square feet of standing seam per day.
Ridge, vents, and final walk
We cap the ridge, install ridge vents for attic airflow, and seal every penetration. Then we magnet-sweep the yard and driveway for nails, and walk the roof with you. You get photos of the finished deck and a workmanship warranty in writing.
Tools & methods
Tools and methods we use on metal roofs
Purpose-built equipment, used by trained technicians, so the job is done accurately the first time.
Standing seam clip system
Concealed clips fasten panels to the deck through the raised seam, so no fastener head is exposed to weather. This is what allows the panels to expand and contract without backing out.
Roofing nail gun
Used for underlayment, ice and water shield, and decking repairs. We set nails to the correct depth so nothing telegraphs through the finished roof.
Moisture meter and infrared camera
We scan the deck for hidden moisture and use the infrared camera to find leak paths and wet insulation before we cover anything up.
Tin snips and utility knife
Panels and flashing are cut by hand where precision matters, especially around chimneys, valleys, and sidewalls where a bad cut means a future leak.
Chalk line and roofing hammer
We snap lines so every panel course runs square, and use the roofing hammer for detail work where a nail gun would be too aggressive.
Safety harness and roofing ladder
Every installer is tied off on steep pitches. We set ladder stabilizers so the ladder does not damage gutters or siding during the job.
Use cases
When Florence homeowners call us for metal
These examples show how the service framework adapts rather than forcing every call through one repair.
Ice dam leaks to a dry attic
A home in the Historic District had water stains on the ceiling every January from ice dams at the north eaves. Insulation in the attic was wet and compressed, and the decking had started to soften. → We replaced the soft decking, set ice and water shield along the full eave, and installed metal panels with balanced ridge ventilation. Two winters later, no ice dams and no ceiling stains.
Storm damage to a full metal upgrade
A limb punched through the roof of a home in Mars Hill during a summer storm. The ceiling was dripping, and the existing shingles were already 14 years old and near end of life. → We tarped the same day, documented the damage for insurance, and installed a full standing seam metal roof once the claim was approved. The job took four days, and the homeowner's cooling bill dropped about 15 percent that August.
Problems we solve
Roof problems metal solves in Florence
Most Florence homeowners call us after one of these four problems shows up. Metal fixes the cause, not just the symptom.
Shingles blowing off after every storm
We install standing seam metal roofing installation in Florence with concealed clips that hold through 110 mph winds. No exposed fasteners, no tabs to lift, nothing for wind to grab. One install replaces years of patch work.
Ice dams forming at the eaves each January
Metal sheds snow and ice instead of holding it. We pair the panels with ice and water shield along the eaves and proper ridge ventilation, which is the combination that stops ice dams on Florence homes.
Hail damage claims every spring
Class 4 impact-rated standing seam panels resist hail that destroys asphalt. After a storm, metal usually needs an inspection rather than a full replacement, which keeps claims off your record.
Ponding water and seam failures on flat roofs
We repair flat roof systems from Firestone and Carlisle SynTec, add tapered insulation to eliminate low spots, and re-seal seams so water drains instead of sitting. For sloped roofs, metal removes the ponding problem entirely.
How much does metal roof installation cost in Florence KY?
Most standing seam metal roof installations in Florence run $12 to $22 per square foot installed, or roughly $24,000 to $44,000 for a typical 2,000 square foot home in 2026. Exposed-fastener panels land lower, around $9 to $14 per square foot. Steep pitches, multiple valleys, and full tear-off push the number up. We quote the whole job upfront, including disposal.
How long does a metal roof last in Florence Kentucky?
A standing seam metal roof in Florence lasts 40 to 70 years, depending on panel gauge and finish. The Kynar 500 paint system on quality panels holds color for 30-plus years. Asphalt shingles in the same climate last 12 to 15. That lifespan gap is why metal roof replacement Florence projects pencil out over a 30-year window.
Is a metal roof worth it in Florence KY?
Yes, if you plan to stay in the home more than 10 years. Metal handles Boone County hail better than asphalt, sheds ice instead of damming, and cuts summer cooling costs 10 to 20 percent. The break-even point against repeated shingle replacements usually lands around year 12 to 15. If you are selling within five years, asphalt may still make more sense.
Can you install metal roofing over existing shingles in Florence KY?
Often yes, if the deck is solid and your local code allows it. We check with a moisture meter and infrared camera first, because trapped moisture under old shingles causes rot. Installing over shingles saves one to two days of tear-off and the dumpster cost, which can knock $1,500 to $3,000 off the job. If the deck is soft, we tear off.
Related services
Other roofing services we handle in Florence
Roofing contractor near me
If you searched roofing contractor near me and landed here, we handle full-service roofing in Florence, from metal installs to shingle repair. One crew, one point of contact, and a written scope before any work begins.
24/7 roofing service
Metal roofs can still take storm damage. Our 24/7 roofing service answers calls after hours for active leaks, missing panels, and emergency tarping across Florence and Boone County, so water does not keep running into your ceiling overnight.
Local roofing contractor
As a local roofing contractor based in Northern Kentucky, we know Florence building stock and how local inspectors want flashing and ventilation done. That means fewer callbacks and a smoother final inspection on your metal roof.Ready when you are
Get your metal roof installation Florence KY quote
We give free estimates on metal roof installation Florence KY projects, and most quotes come back within 48 hours. Licensed, insured, and warrantied. Call (844) 799-4703 and we will schedule a roof inspection this week.
Talk with the local team
Request Metal roof installation
Call (844) 799-4703 any time, day or night, and a real person picks up. For standard inspections and estimates we schedule within 24 to 48 hours, and emergency leak calls get same-day priority. You can also email info@revixionlab.com with photos of the problem and we will get back to you with next steps.